Unanswered Questions in input current

Hello, what I need to visual the current and frequency?

I want to see on VRM / Touch 70 a few data's.

AC In from Shore/Generator to my Skylla Charger.

AC Out from my Phoenix Inverter.

Skylla I is connected with VE.CAN with the Cerbo.

Phoenix Smart is connected with VE.Direct with the Cerbo.

And is there any Tile in GUI to visual this without a Multi/Quattro?

Here is an example what I want to see, but without a Multi/Quattro.

Best regards Robert

[image]

And here is my Touch 70

[image]

I've been trying to figure this out. Spent a lot of time researching and today tried for several hours, but came up with nothing. Even tried using a Self Consumption Hub, but ended up with: Using VECONFIG I set it up and then you select a policy. All but two are deprecated. I tried the two and I could not get any AC power, I received a Error 6 - Error in DDC Program.

Victron, here is the ideal solution, which might not exist in your firmware, but it is to dynamically limit the AC Input based on the solar and based on the AC Demand.

I.E. If the AC demand is 2000 watts and we have 500 watts of solar, limit the AC Input to 1500 watts. If the Solar is 1500 watts and demand is less than that, switch to Inverter. I'm hoping, if the AC Input limiter cannot handle frequent changes, then give us a threshold. The goal is to use direct solar and avoid tapping the batteries so we aren't charge/discharge.

Please point me in the right direction, or take this as a feature request.

Hello All,

I have an MPPT 100/20 48V charge controller connected to a small battery. I would like to track the available Amp output from the panels. The display notates the Voltage, but does not display Amps unless there is flow from panels into the battery (Perhaps I'm misreading this?). Either way, is this possible? I've tried under trends but that also doesn't seem to solve the display.

I've looked for other solutions for active data recording of the Amp output - I'm open to suggestions because I haven't found one. Would ideally like to see both Voltage and Amp current recorded together.

Thanks!

[image]

[image]

I always notice that I consume more electricity than I produce. At least according to the meter. Today again 31 kWh produced and 43 kWh consumed and the battery is so full again
as before. The Solarprdokution is measured with an ET 340. The consumption data is measured by the three Multiplus on each phase. The battery status comes from the BMS. I see every hour more consumption than production and still the battery is charging.

[image]

The input lockout works for 24 hours. After that it failed. I had to restore setting and it work again. This processed was successful the last two incident. Now it appear the input lockout feature failed even if I restore from previous settings or manual co fig. Please help. Thank you.

The Victron model (https://www.victronenergy.com/live/energy-meters:et112) is a single phase 240v. Is there a single phase 110v equivalent available to feed AC current consumption to my Cerbo?

Thanks

I have a Quattro 24/5000. When I add an AC load, the Quattro drops the AC 1 In current (connected to a 4800 W generator). The inverter/batteries make up the difference. See attached screen shot.

Settings: 120V, 60hz, Power Assist = on; Boost Factor = 2.0, max; AC 1 input current limit = 15 amps. See screen shots. The only difference in conditions in these two screen shots is the AC load applied.

This is strange behavor and I am at a loss. Any ideas?

[image]

[image]

I have done a re-install on a previous 12 volt setup in my Landcruiser. Prior to removing this setup the BMV-702 was functioning correctly.

Now after a re-install, the BMV-702 is working and connecting via the app to my phone but it is not reading any current draw when load is applied to the auxilary battery.

I have re-installed using the factory wiring diagram and checked it over, so it should be correctly wired.

If I turn the ignition on the app with begin reading current draw, but in large amounts.

I have reset factory settings, re-installed and updated the app with the latest firmware.

Can anyone please help.