Remote control of Phoenix 12/375 via MPPT 100/20

Question

question

petter asked Jun 5, '19

Remote control of Phoenix 12/375 via MPPT 100/20

Hi!

Ive got a MPPT 100/20 regulator and a Phoenix 12/375 inverter.

I would like to control the inverter with the MPPT 100/20 regulator and now I wonder …

Do I just need to connect the left side of the remote control on the inverter to the load + output on the regulator or do I need the special cable “ASS030550100”. The manual is not obvious.

Best regards

Petter

Battery Protect

screenshot-2019-06-05-at-214028.png (959.1 KiB)

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Modifications Space

Node Red Space

Answer 1 · 2019-06-05T20:40:33Z

wkirby answered · Jun 05, 2019 at 08:40 PM

Yes, you need to use the inverting on-off cable (ASS030550100)

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

petter commented · Jun 06, 2019 at 05:27 AM

Thanks for answer, I will order one!

0 ·

Answer 2 · 2019-06-05T23:23:13Z

ripper answered · Jun 05, 2019 at 11:23 PM

Or a relay normally open (NO) Instead of the bridge two cables towards the relay contacts and actuating via the 100/20. Cheaper but needs some juice

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

petter commented · Jun 06, 2019 at 05:29 AM

Thanks, I will go for the inverter on-off cable

0 ·

Answer 3 · 2020-08-15T17:42:16Z

hardstuff answered · Aug 15, 2020 at 05:42 PM

Or is this connection purpose tell to MPPT current Phoenix 375 VA workload and wake it up to produce More "juice" from panel ? Manual of MPPT 100/20 says there is no need for special cable, just one ordinary wire between remote left and MPPT's load output. Olen models like 350 W Phoenix need special cable says manual

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 4 · 2020-08-15T17:46:16Z

hardstuff answered · Aug 15, 2020 at 05:46 PM

Check this picture, it is just ordinary electric wire for Phoenix models 375 VA

20200814-112033.jpg (1.8 MiB)

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 5 · 2020-08-16T07:18:13Z

hardstuff answered · Aug 16, 2020 at 07:18 AM

Maybe relay is built-in these 375 VA models, if just a wire is good to go ?

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 6 · 2020-08-31T03:24:44Z

marioc answered · Aug 31, 2020 at 03:24 AM

There is no need of an special cable with the 12/375, a simple cable connected as you indicate works fine with mine.

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

question