New recent issue with a Cerbo GX V2. I’ve had this running for several month on my bench testing a new configuration. Connected to Wi-Fi no problem and have been able to do OTA updates to the firmware and some packages. Recently I noticed I was unable to update firmware OTA. Upon further review …

Additionally, I have attempted to connected it to a cellular Wi-Fi hotspot on my phone to eliminate the local network as an issue, but unable to get it to connect. Very flakey behavior. keyboard doesn’t pop up when attempting to add a password, wont remember the password once entered and doesn’t s…

The Gateway IP is missing, should lock like below I’m also wondering about the IP address of the DNS server. I would expect the IP address to be 192.168.1.1 = expected gateway address, and not 6 at the end. [grafik] Are you also using the Ethernet interface?

@DirkW DNS server is being pointed at a dual PiHole installation. Nothing new there, has been working like this since new. However, I did suspend the Piholes (revert it back to what you would suspect 192.168.1.1), and no change observed. Additionally, attempted to connect to a cellular hotspot t…

Please unplug the Ethernet connector to test it and reboot the Cerbo. I also found it very easy to set up the Wi-Fi with Victron Connect via Bluetooth, even on a brand new device, without having to connect a cable Test your smartphone hotspot and please try it again.

@DirkW This fixed the issue with the Wi-Fi. I am doing an OTA update back to v3.67. That is working. I’ll reattempt connection over ethernet to the MFD after that, but I hope I dont have to choose 1 or the other…that MFD connection is main access point to the system/boat.

As soon as I attempt to reconnect the MFD integration, the gateway address drops out. Unplug the MFD, gateway address returns. This was working before no issues…

Please type in 0.0.0.0 as Ethernet Gateway address [image] VRM is not uploading when is conected to Garmin MDF DIY As you have the GX device ethernet port in use for a non internet connection such as energy meter, MFD and wifi connection for internet this migh…

Inputing 0.0.0.0 as the gateway on the Ethernet breaks the link to the MFD. I get a “No hardware Detected”. Going back to Automatic Configuration on the Ethernet breaks my Wi-Fi connection. Let me look at what I have on the other installation… Hmmm….

Disregard…everything seems to be up and running as expect…just took a little longer than expected. For the record… Wi-fi Connection up with local and remote access via VRM Ethernet Connection connected via Ethernet port to Raymarine Axiom with the gateway manually configured to 0.0.0.0 Any idea …

Cerbo GX V2 not obtaining a network gateway address - Unable to update OTA

Q&A and troubleshooting

DirkW 20 December 2025 15:35 8

Please type in 0.0.0.0 as Ethernet Gateway address

Topic		Replies	Views
Cerbo GX stopped updating to the website DIY diy , vrm , cerbo_gx , cerbo-gx	5	93	11 August 2026
Cerbo GX MkII firmware not updating DIY beginner , gx_device , cerbo_gx	6	141	18 May 2026
Cerbo GX is not updating VRM portal DIY marine , beginner , vrm , gx_device , cerbo_gx	2	222	28 October 2025
Cerbo GX (Mrk1) internet issue after 3.62 DIY diy , vrm , gx_device , cerbo_gx	6	242	9 July 2025
Cerbo GX Ethernet connection not working correctly Q&A and troubleshooting diy , ess , gx_device , cerbo_gx	12	940	13 April 2025

Cerbo GX V2 not obtaining a network gateway address - Unable to update OTA

Related topics