I have configured the ESS with AC coupling in which I have installed 2 Huawei inverters, 2 Victron multiplus ii inverters, the question is, Yesterday at noon with the batteries already charged to 100%, it took a while for the Huawei inverters to frequently block and the victrona equipment, unable to absorb the power, blocked and restarted twice. What parameters can I adjust so that this does not happen again? Currently I have these values in the overfrequency control for cutting for huawei, reduce power: 50.30Hz power at minimum: 52’7Hz disconnection: 53Hz, thank you very much for the help!!

Have you set the Huawei grid compliance settings?

Yes, in Huawei the overfrequency control is activated with the same values indicated. I think it was a failure due to the speed at which it reacted. The question is whether I should lower the power limitation controls a little so that it cuts off earlier due to frequency.

Did you enable the multiplus battery monitor or are you using a shunt?

They are lithium pyl batteries with bms, it is enabled

Do you have communicatoin from the battery BMS? You could try lower the absorbtion voltage what you could be seeing is the battery disconecting due to cell overvoltage protection and the multi has nowhere to put the power.

I have 6 Pylontech batteries of 4.8Kwh, the voltages are set like this: Absortion voltage–> 52V Float Voltage → 51V In the MPPT absorption at 52V What values do you recommend?

If they are 15 cells try 50V ABS then if you still have issues try 49 48V. I have a 36kwh battery with 2x 5kw ac inverters and a 48/100 mppt and I am grid connected and have issues when the sun is out there can be 13-15kw of solar. I don’t know how your communication is setup but this does help. You can adjust the battery % when you hit absorption. This can fine-tune where you are based on the battery BMS. You can also right-click on the battery and send the estimated SOC when you upload the config. [image]

At the settings area I applied for SUN2000-4KTL Iin the ESS assistant, I changed them to 50.2, 51.48 and 51.5. These settings are matching the ones off the PV inverter.

Hello! I am having a similar setup as yours. I am having already a huawei inverter installed and i want to add one multiplus II to create a microgrid. I am having difficulties with the huawei settings. Can you tell me where did you find the overfrequency control settings? All i can find is the overfrequency protection that shuts down the inverter. Thanks.

Hello, I have a Huawei Sun PV inverter and want to install MP 2. I understand the settings of frequency shifting to reduce the PV power in case of no grid power. But is it also possible to reduce the grid export to a certain value of 0 in case of normal grid connection? If so, should the Huawei be connected on the AC-in or AC-out or does that not matter? Want to explore this option as the costs for delivering Power to the grid are increasing.

Mutiplus II ESS AC Coupling

Q&A and troubleshooting

Radunre 10 January 2026 08:28 12

Limited feed-in is officially not supported with Huawei on-grid inverters coupled into Victron environment.

Some hints have been discussed here.

MultiPlus uses frequency shifting during OFF-Grid only.

Topic		Replies	Views
Sistema Huawei Sun2000 3ktl-l1 AC-Coupling con victron Multiplus II, en 120/240VAC DIY split-phase	8	1429	31 May 2025
Multiplus II and Huawei AC-Coupling DIY diy , offgrid , multiplus-ii	22	3563	2 March 2026
Multiplus PV Frequency shift - Pylontech Q&A and troubleshooting beginner , pv_inverter , vrm , multiplus-ii	18	574	20 January 2026
How to configure Multi-Plus II to charge battery from AC side PV Q&A and troubleshooting diy , multiplus_2_gx , pylontech , node-red , cerbo_gx	12	337	21 January 2026
Multiplus II disconnects often from grid due to overvoltages Q&A and troubleshooting ess , feed_in , multiplus-ii , fronius	6	768	27 November 2025

Mutiplus II ESS AC Coupling

Related topics