Hi, I have an question you might know the answer to :slight_smile: I have an Basen-Green 15KWh battery. I want it to connect to the Cerbo-GX. When I connect the Battery to the Cerbo-GX it does not show up. In the software I configured the battery CAN port for “Victron” The battery comes with an…

ik heb de accu op de BMS-can van de cerbo aangesloten dus je gaat van de can van de accu naar BMS-can van de cerbo ook moet je de can bus van de accu via software (rs485 ) of via app van basengreen op Victron staan. voor de kabel heb ik de volgende pinout gebruikt: kant victron: Pin 8 CAN-L / Pin …

Although CAN communication is of a differential type, sometimes is better to also have the GND wire connected. If you set the battery as Victron protocol, then that protocol is 250kbps and you can only connect the battery to VE.CAN port on Cerbo (which you did) and then you must setup the port acco…

Hi Alex, I followed you advice and connected the CAN Port of the battery to the BMS-Can of the Cerbo. Changed the battery CAN-Type to “Pylon” Still the Cerbo does not recognise the port. Do I need to terminate the other BMS-Can port on the Cerbo? Do I need a specific setting changed in the Cerbo f…

Usually at Cerbo’s end you need to terminate the CAN network, bar the situation where you daisy chain another device. No, you don’t need to change anything in Cerbo for monitoring the battery. All work out of the box, at least for BMS-Can port. For the VE.Can port, you need to configure the profile…

The cable that came with the battery was a bit wanky. So I’f created a new one. When I look at the port statistics of the VE.Can port. It shows some port errors. [Screenshot 2024-09-15 at 17.52.43] I’f changed the VE.Can port profile to CAN-bus BMS LV (500 kbits/s) Still no luck Then try’d the…

ik hoop dat het al gelukt is maar mocht dat niet zo zijn ik heb een basengreen accu draaien op mijn systeem. mocht je vragen hebben dan kun je die stellen

[image] Frank Quint: mocht je vragen hebben dan kun je die stellen Hoi Frank, Harstikke bedankt voor je aanbieding :slight_smile: Ik krijg de accu niet op de Cerbo gekoppeld. Is dat jou wel gelukt. Op het filmpje zie je dat ze de accu op de MPII aansluiten. Dat ben ik nu aan het proberen.…

Hi, I am Dutch and think this is also a issue for more Basengreen user therefore I answer in English. I was also struggling with the setup / connection and you point me in the right direction. But I think Frank you make a small mistake / typo. I think on the Basengreen the pin 4 is CAN-H instead…

Hi Reinoud, You are right CAN-H Pin 4 and CAN-L Pin 5 on the basengreen side. (of topic yes you can just use the software of basen green go to config tab and enter the password at the bottom right. password: 888888 )

[WhatsApp Image 2024-09-20 at 10.51.19] Have you set the pins like this?

Basen-Green 15KWh battery connection to Cerbo-GX fails

DIY

Frankquint (Frank Quint) 20 September 2024 17:18 12

Yes

Topic		Replies	Views
BasenGreen 48v 16KWh battery connection to Cerbo-GX mk2 DIY beginner , domestic , bms , cerbo_gx , basengreen	0	172	27 March 2025
No BMS CAN connection with Cerbo GX DIY bms , cerbo_gx , basengreen	27	2153	29 January 2025
Connexion batterie EcoWorthy rack 51,2 V au Cerbo GX (bus CAN) Communauté francophone expert , bms , cerbo_gx	1	143	25 August 2025
EG4 LL-S not detected on Cerbo GX Q&A and troubleshooting diy , multiplus-ii , victron_community , backup , cerbo_gx	7	684	31 December 2024
CerboGX Mk2 with V TAC Battery VT-48200B Q&A and troubleshooting beginner , bms	19	179	8 December 2025

Basen-Green 15KWh battery connection to Cerbo-GX fails

Related topics