venus os large
Two Multiplus II in series
[image]
I am working on installing a Multiplus II 48/5000 at my home, where I already have an on-grid photovoltaic inverter SMA Sunny Boy 4kW and I have some questions I haven't found answers anywhere:
1. Is it possible to install two Multiplus II inverters in series (one of them connected to the other critical loads output) with non-shared batteries? How should I configure them? That would enable me to add a new Multiplus II in the future with another new battery on grid-parallel mode connected to first Multiplus II critical loads output.
1.1 If 1. question is possible, should I configure second one to not exporting to grid? Or first one could use frequency shifting (or similar) to control how much energy could export the second one?
1.2 Continuation of 1.1 question. Would be possible to have SMA Sunny Boy 4kW connected to the same critical loads output than second Multiplus II, having both controlled by frequency shifting? Or that is not possible as maximum power would exceed Multiplus II maximum power?
It appears a similar configuration could be done by using CerboGX large firmware, to be able to use Node-red to control some inputs:
- first Multiplus II critical loads frequency (could be updated depending on first Multiplus II is able to receive more power from critical loads or it cannot accept many more
- first Multiplus II AC In grid status (availabe/not available)
And to be able to control some things:
- second Multiplus II power exportation limit, being configure to 0 power exporattion into second Multiplus II if grid on first Multiplus II is disconnected
I've seen some other questions about similar solutions, but they were trying to control batteries load between two Multiplus II at the same time at the same battery load. I'm not interested on that. What I'm looking for is to:
1. If second Multiplus II (with AC In connected to first Multiplus II critical loads AC OUT) has batteries fully loaded, then it will share power with the other one if the other requires it; if the other doesn't require it and external grid is connected, power could be exported to grid; and if the other doesn't require it and external grid is disconnected, 0 power export should be configured into second Multiplus II
2. If first Multiplus II (connected to grid and with second Multiplus II connected to it's critical loads AC OUT) has batteries fully loaded, if second Multiplus II requires power, first Multiplus II can provide that power as if it were coming from real grid
tcircuns asked
[image]
I am working on installing a Multiplus II 48/5000 at my home, where I already have an on-grid photovoltaic inverter SMA Sunny Boy 4kW and I have some questions I haven't found answers anywhere:
1. Is it possible to install two Multiplus II inverters in series (one of them connected to the other critical loads output) with non-shared batteries? How should I configure them? That would enable me to add a new Multiplus II in the future with another new battery on grid-parallel mode connected to first Multiplus II critical loads output.
1.1 If 1. question is possible, should I configure second one to not exporting to grid? Or first one could use frequency shifting (or similar) to control how much energy could export the second one?
1.2 Continuation of 1.1 question. Would be possible to have SMA Sunny Boy 4kW connected to the same critical loads output than second Multiplus II, having both controlled by frequency shifting? Or that is not possible as maximum power would exceed Multiplus II maximum power?
It appears a similar configuration could be done by using CerboGX large firmware, to be able to use Node-red to control some inputs:
- first Multiplus II critical loads frequency (could be updated depending on first Multiplus II is able to receive more power from critical loads or it cannot accept many more
- first Multiplus II AC In grid status (availabe/not available)
And to be able to control some things:
- second Multiplus II power exportation limit, being configure to 0 power exporattion into second Multiplus II if grid on first Multiplus II is disconnected
I've seen some other questions about similar solutions, but they were trying to control batteries load between two Multiplus II at the same time at the same battery load. I'm not interested on that. What I'm looking for is to:
1. If second Multiplus II (with AC In connected to first Multiplus II critical loads AC OUT) has batteries fully loaded, then it will share power with the other one if the other requires it; if the other doesn't require it and external grid is connected, power could be exported to grid; and if the other doesn't require it and external grid is disconnected, 0 power export should be configured into second Multiplus II
2. If first Multiplus II (connected to grid and with second Multiplus II connected to it's critical loads AC OUT) has batteries fully loaded, if second Multiplus II requires power, first Multiplus II can provide that power as if it were coming from real grid
0 Answers
Expected traffic to the mqtt{1 to 128}.victronenergy.com server farm?
I am running Venus-large and have a fairly extensive Node-Red flow consisting of about 100 nodes. My router is reporting a permanent TCP/IP session with one of the mqtt{1 to 128}.victronenergy.com servers with constant traffic of just over 10 kbit/s upload and just under 1 kbit/s download. This seems high to me but maybe it's because of my 100-node flow. Is this level of traffic to be expected?
paulcooper asked
I am running Venus-large and have a fairly extensive Node-Red flow consisting of about 100 nodes. My router is reporting a permanent TCP/IP session with one of the mqtt{1 to 128}.victronenergy.com servers with constant traffic of just over 10 kbit/s upload and just under 1 kbit/s download. This seems high to me but maybe it's because of my 100-node flow. Is this level of traffic to be expected?
paulcooper answered ·
1 Answer
Display on Cerbo with Venus OS Large
I understand support for Venus OS Large is not available from Victron, but this is just a quick one that maybe a member here may have an answer for?
Installed 2.72 Large on my Cerbo and I found the screen attached to the HDMI output was around 1/4 the size (shrunk by half width and half height).
When I booted the standard 2.72, the screen went back to taking up full size.
Any ideas to get the Venus OS Large to use the screen in the same way as standard OS?
FYI, these are the versions ....
[image]
wildebus asked
I understand support for Venus OS Large is not available from Victron, but this is just a quick one that maybe a member here may have an answer for?
Installed 2.72 Large on my Cerbo and I found the screen attached to the HDMI output was around 1/4 the size (shrunk by half width and half height).
When I booted the standard 2.72, the screen went back to taking up full size.
Any ideas to get the Venus OS Large to use the screen in the same way as standard OS?
FYI, these are the versions ....
[image]
0 Answers
Raymarine integration in nk2 network with several Victron devices that send battery data.
I have several devices in nk2 networks that send battery data such as Multiplus, MPPT, rec-bms and smart shunnt. Without modifications, only two batteries will appear on Raymarine instruments. (I have 3 battery banks) Based on testing to display battery data correctly on Raymarine, we have used a programmable interface and changed "device instance" and "data instance" to see how data is presented on Raymarine display. Changing the device instance as described in the Victron GX manual chapter 11.5.4 does not change anything on Raymarine instruments! (Tried this from the venus os menu as well) When we change the data instance, the battery is presented correctly. This was also the case on thread eg posted about 1 year ago about data instance. The question is why device instance is made available in menu on Venus os and manual describe that change of data instance is not recommended?
Anyone have experiences to share that can confirm this? Do other manufacturers use device instance for numbering batteries?
Jonny Sollid asked
I have several devices in nk2 networks that send battery data such as Multiplus, MPPT, rec-bms and smart shunnt. Without modifications, only two batteries will appear on Raymarine instruments. (I have 3 battery banks) Based on testing to display battery data correctly on Raymarine, we have used a programmable interface and changed "device instance" and "data instance" to see how data is presented on Raymarine display. Changing the device instance as described in the Victron GX manual chapter 11.5.4 does not change anything on Raymarine instruments! (Tried this from the venus os menu as well) When we change the data instance, the battery is presented correctly. This was also the case on thread eg posted about 1 year ago about data instance. The question is why device instance is made available in menu on Venus os and manual describe that change of data instance is not recommended?
Anyone have experiences to share that can confirm this? Do other manufacturers use device instance for numbering batteries?
sunnycoastgreg commented ·
4 Answers
