# Victron Energy GX Tank 140

**URL:** <https://community.victronenergy.com/t/victron-energy-gx-tank-140/43636>\
**Category:** DIY\
**Created:** [18 August 2025 09:16 UTC](https://community.victronenergy.com/t/victron-energy-gx-tank-140/43636 "2025-08-18T09:16:53Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![vikingwoman](https://avatars.discourse-cdn.com/v4/letter/v/ac91a4/32.png) [@vikingwoman](https://community.victronenergy.com/u/vikingwoman)\
**Post date:** [18 August 2025 09:16 UTC](https://community.victronenergy.com/t/victron-energy-gx-tank-140/43636/1 "2025-08-18T09:16:53Z")

</div>

I find the product difficult to use. The only tank sensors that are easy to obtain are resistive. I need to use a converter BEP 600-TLM-SIF Tank Level Monitor Sender Interface Module for every input.. This takes resistive sensor and gives a 0-5 volt output to Tank 140. I wish Victron would correct the Tank 140 to accept resistance sensors. The cost is very high to use the Tank 140 option.

---

<div class="post-metadata">

**Author:** ![M\_Lange](https://dub1.discourse-cdn.com/victron/user_avatar/community.victronenergy.com/m_lange/32/16_2.png) [@M\_Lange](https://community.victronenergy.com/u/M_Lange)\
**Post date:** [18 August 2025 09:38 UTC](https://community.victronenergy.com/t/victron-energy-gx-tank-140/43636/2 "2025-08-18T09:38:47Z")

</div>

What GX device do you have?  
The Cerbo GX has 4 inputs for resistive sensors, the Ekrano GX has 3.

---

<div class="post-metadata">

**Author:** ![vikingwoman](https://avatars.discourse-cdn.com/v4/letter/v/ac91a4/32.png) [@vikingwoman](https://community.victronenergy.com/u/vikingwoman)\
**Post date:** [18 August 2025 12:59 UTC](https://community.victronenergy.com/t/victron-energy-gx-tank-140/43636/3 "2025-08-18T12:59:44Z")

</div>

I have 7 tanks to monitor. Four use the Cerbo GX Mk2 and added Tank 140 for the other three.

---

<div class="post-metadata">

**Author:** ![vikingwoman](https://avatars.discourse-cdn.com/v4/letter/v/ac91a4/32.png) [@vikingwoman](https://community.victronenergy.com/u/vikingwoman)\
**Post date:** [18 August 2025 13:14 UTC](https://community.victronenergy.com/t/victron-energy-gx-tank-140/43636/4 "2025-08-18T13:14:14Z")

</div>

Yes it would be good if Tank 140 was for resistive sensors. Four tanks fuel ; three tanks water.

---

<div class="post-metadata">

**Author:** ![DaveBoucher](https://avatars.discourse-cdn.com/v4/letter/d/e19adc/32.png) [@DaveBoucher](https://community.victronenergy.com/u/DaveBoucher)\
**Post date:** [29 May 2026 05:20 UTC](https://community.victronenergy.com/t/victron-energy-gx-tank-140/43636/5 "2026-05-29T05:20:39Z")

</div>

add another cebo gx to give another 4 resistance levels. configure new cerbo to be off line…it’s in the cerbo manual