Good day! A fresh new thread for v3.80 beta feedback. Change log below, and first please make yourself aware with the beta testing instructions: Instructions 1 of 3: Venus OS beta testing & how to join/install In case you don’t know what this message is about, please start with reading this link ,…

[image] Jeroen: Support custom names in multi-tanks setups Really great to see this fix in after so long having Fuel [100], Fuel [101], etc! I tested and it’s working great with my four N2K senders. The capacity setting remains greyed out and unusable on N2k devices, and capacity (like name…

Since 3.80-32 I get “High Discharge Current Alerts” on short load peaks… Pylontech Battery. Peaks are around 50A.

Starting with version v3.80~33/v3.80~32 my SolarEdge SE4000 inverter, connected via modbus proxy, gets Active Power Limit set to 0, effectively disabling the inverter’s solar output. Switching back to the stable firmware fixes the issue. I have not seen this behaviour prior to v3.80~33 and came from…

I have reverted that change. The idea was that a loss of communication will shut down SolarEdge inverters, like we do with inverters that support Sunspec-2018. In practice, it will require people to disable the limiting option in the PV-inverter menu whenever they are not using limiting, and I fear …

I’ve tried out the new virtual indicators. They show up in the remote console but not in the VRM switch pane. I’m using betavrm. Is that supposed to work already?

I had v3.80~27 running, uptime was over 2 weeks Today, i was looking at the local GUI, as every day While looking, after a few seconds, it restarted I saw a messeage, something like “installing firmware” after that, i was back to v3.80~14 I also didn´t see any backup configurations in the firmw…

when reverting to #14 - i still have the new linux The system is unusable now, reboots every few minutes How could i bring it back to a stable state ? With #27 it was running perfectly for over 2 weeks

Hi, I use two Shelly 1PM Gen 4 and one EM Mini Gen 4 to measure my PV inverters. On v3.80~27, they are recognized most of the time and run satisfactorily. When I install ~33, they are no longer displayed. I thought they aren’t dimmable!? Furthermore, even on ~27, I have the issue that the EM Mini’…

I make a new thread for it last week no response yet. Same issue with the shelly mini. I looking now to roll back to 25.

Hi, For the EM Series, there was a bug, that the “wrong counter” was read, “Energy Forward” rather than “Energy Reversed”. I think that was fixed, So if your EM was logically working until now, it is now “logically wrong orientation” still counting on the “Energy Forward” which is no longer read. …

Venus OS v3.80~39 available for public testing

Beta testing Venus OS beta testing

Topic		Replies	Views
V3.64 Node-RED - Not connected to D-Bus error Node-RED diy , domestic , node-red , gx_device , cerbo_gx	47	1326	October 24, 2025
Shelly 3PM einbinden Deutschsprachiger Bereich vrm , cerbo_gx	81	4027	April 23, 2026
Venus OS v3.70 release version - After reboot "low battery voltage" alarm Q&A and troubleshooting	13	562	March 6, 2026
Where is Node-Red gone in Venus 3.60? Node-RED diy , domestic , gx_device	80	1671	June 19, 2025
Hinweis Upgrade von 3.67 auf 3.70 mit Node-Red Virt Grid Meter Regelung setzt aus Deutschsprachiger Bereich vrm	24	287	March 29, 2026

Venus OS v3.80~39 available for public testing

Related topics