I have three Shelly devices and 4 different problems: Shelly PlugS Gen3 | 1.7.5 Shelly 1PM Gen4 | 1.7.5 Shelly Pro3EM | 1.7.5 Problem 1: The Pro3EM reporting in VRM is using the device total almost every time the Cerbo resets. So once every so many weeks due to an update for example, I have tho…

Hi @k_delaat Thanks for reporting. I’ve had a closer look and found the cause of the issue. Will be fixed in the next release.

Hi @kudos50 , Thanks for the report. This will be fixed soon.

Hi Rein, I just applied your latest changes on the fresh 14 beta and the missing totals from the previous post have been resolved. I did not notice this earlier but I think the same applies to the Pro 3EM. There simply seems to be more information now. I still however seem to have a strange/mixed d…

Hi @kudos50 , I just applied your latest changes on the fresh 14 beta and the missing totals from the previous post have been resolved. Good, fix will be available officially in beta soon. I have 2 former acload ghost devices under advanced That is a known issue in VRM. You should be able to …

Nope, that’s the problem. They don’t show up in the device list but do show up under advanced statistics. So I cannot delete them.

Not related but since 3.80 seems to be a Shelly enabler; any plans on adding evcharger to the list of supported types ? Asking because I have a flow for a virtual device (Eastron SDM630-Wifi) but I don’t want to spend time on rearranging the wiring closet for a node-red solution if support for shel…

Hi @rzee When the Cerbo looses network connection to all shelly devices, it is unable to restore the connection. In my case, the switch was off for a bit yesterday. I noticed it this morning and restarted dbus-shelly to fix it. Prior to restarting, the Shelly devices no longer appeared in the devic…

I also noticed this open in victronconnect button for shelly switches that are also an energy meter (e.g. shelly pm4) Does that button need to be there? is there a victronconnect beta that supports configuring shelly devices that I’m missing?

Hi @cbr , I also noticed this open in victronconnect button for shelly switches that are also an energy meter (e.g. shelly pm4) Does that button need to be there? is there a victronconnect beta that supports configuring shelly devices that I’m missing? No that button should not be there and will…

Thanks for reporting, I’ll look into it.

Hi @kudos50 - not to go off topic, but on v3.80 are you able to have different names for the Pro3EM’s “energy meter” and “switch” components? I’d like to use a similar device to measure my heat pump consumption, though plan on using the switch component to trigger a load shed contactor. So that re…

V3.80~8 – Shelly naming and VRM issues

Beta testing

A-P May 18, 2026, 10:34am 21

Thanks @rzee! On this topic, it also seems that having multiple meters under the heat pump role messes with VRM reporting. Two heat pumps causes issues with VRM consumption

Topic		Replies	Views
Venus 3.70 released Q&A and troubleshooting venus_os	16	2145	March 20, 2026
Venus OS v3.70 - Shelly support Q&A and troubleshooting expert , ekrano_gx	0	1590	March 2, 2026
Shelly EM Gen3 - Switch detected, but EM1 channels missing from Cerbo device list DIY diy , cerbo_gx , cerbo-gx	4	112	July 13, 2026
Shelly 3em nicht sichtbar in Remote Console und im VRM Deutschsprachiger Bereich beginner , vrm , multi_rs , cerbo_gx	41	1113	August 15, 2025
VenusOS v3.70 Shelly integration only showing four shelly devices Q&A and troubleshooting diy , gx_device , cerbo_gx	8	559	March 7, 2026

V3.80~8 – Shelly naming and VRM issues

Related topics