# CerboGX with Multiplus 2000/12/50

**URL:** <https://community.victronenergy.com/t/cerbogx-with-multiplus-2000-12-50/12380>\
**Category:** DIY\
**Tags:** rv, battery\_balancer, cerbo\_gx, diy, multiplus\
**Created:** [19 November 2024 22:19 UTC](https://community.victronenergy.com/t/cerbogx-with-multiplus-2000-12-50/12380 "2024-11-19T22:19:00Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![caymann](https://avatars.discourse-cdn.com/v4/letter/c/91b2a8/32.png) [@caymann](https://community.victronenergy.com/u/caymann)\
**Post date:** [19 November 2024 22:19 UTC](https://community.victronenergy.com/t/cerbogx-with-multiplus-2000-12-50/12380/1 "2024-11-19T22:19:01Z")

</div>

I connected the VE.bus cable between CerboGX and Multiplus 2000/12/50 so that i could access the battery charging parameters using the CerboGX user panel. The only thing i can see for battery related settings is “Equalize”. I was hoping to see other settings like - type of battery (Lead Acid, AGM, GelCell, LiFePO4 etc), their charge settings and charge profile etc. I don’t even see the state of battery charge on the CerboGX. Should these be not there? I have latest firmware.

---

<div class="post-metadata">

**Author:** ![Justin](https://dub1.discourse-cdn.com/victron/user_avatar/community.victronenergy.com/justin/32/24_2.png) [@Justin](https://community.victronenergy.com/u/Justin)\
**Post date:** [19 November 2024 23:34 UTC](https://community.victronenergy.com/t/cerbogx-with-multiplus-2000-12-50/12380/2 "2024-11-19T23:34:03Z")

</div>

Programming a MultiPlus through the Cerbo is not possible, no. The configuration options and their respective requirements can be found in the “Configuration” section of the MultiPlus user manual -not sure if you have the 120v or the 230v model, but the manuals should be basically the same so here’s the section from the 120v model: [5.&nbsp;Configuration](https://www.victronenergy.com/media/pg/MultiPlus_2kVA_120V/en/configuration.html#UUID-06af5fde-f6c3-30fe-09cd-0d4eb9848957)

---

<div class="post-metadata">

**Author:** ![jabrockert](https://avatars.discourse-cdn.com/v4/letter/j/439d5e/32.png) [@jabrockert](https://community.victronenergy.com/u/jabrockert)\
**Post date:** [26 January 2025 22:48 UTC](https://community.victronenergy.com/t/cerbogx-with-multiplus-2000-12-50/12380/3 "2025-01-26T22:48:10Z")

</div>

Your going to need the MK3-USB to PC from Victron with the Victron Connect app to get to those params

---

<div class="post-metadata">

**Author:** ![Yachtbird](https://avatars.discourse-cdn.com/v4/letter/y/6f9a4e/32.png) [@Yachtbird](https://community.victronenergy.com/u/Yachtbird)\
**Post date:** [27 January 2025 01:07 UTC](https://community.victronenergy.com/t/cerbogx-with-multiplus-2000-12-50/12380/4 "2025-01-27T01:07:38Z")

</div>

@caymann you could connect the CerboGx to the VRM, download the Multiplus program and launch it with the VE.Configure 3 program. That way you can access all of the parameters, adjust them and then upload it back to the Multiplus.