# Blue Smart IP65 12/15 charger not charging LiFePo4 battery

**URL:** <https://community.victronenergy.com/t/blue-smart-ip65-12-15-charger-not-charging-lifepo4-battery/42286>\
**Category:** DIY\
**Tags:** bluesmart\_ip65, lithium\_battery, beginner\
**Created:** [7 August 2025 09:18 UTC](https://community.victronenergy.com/t/blue-smart-ip65-12-15-charger-not-charging-lifepo4-battery/42286 "2025-08-07T09:18:14Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![Olifant](https://avatars.discourse-cdn.com/v4/letter/o/54ee81/32.png) [@Olifant](https://community.victronenergy.com/u/Olifant)\
**Post date:** [7 August 2025 09:18 UTC](https://community.victronenergy.com/t/blue-smart-ip65-12-15-charger-not-charging-lifepo4-battery/42286/1 "2025-08-07T09:18:14Z")

</div>

I have attempted to charge a new Renogy 200Ah Bluetooth LiFePo4 with a Blue Smart IP65 12/15 charger. The charger is set to the LiFePo4 preset. The battery initially told me that its capacity was 45.56% and the voltage 13.2V (as delivered). The charger is connected directly to the terminals of the battery. There is nothing else in the system.

When I powered up the charger, it did the initial test, the bulk indicator illuminated momentarily, and then switched to absorption. The charge rate was initially 1A at 13.2V and gradually decreased to 0.7A at 13.2V. After being left overnight to charge, the charger output was 0A at 13.2V. The battery capacity had increased to 46.86% at 13.2V.

I have repeated the process several times but the charger behaves the same way every time. It will not output 15A at 14.2V as defined by the LiFePo4 preset.

The charger firmware has been updated to v3.61.

Unfortunately, I have only one LiFePo4 battery and only one charger suitable for charging it, so swapping out for known good units is not possible.

Am I doing something wrong with the charger settings, for example, or is it more likely that the charger (or battery) is faulty?

Edit: I have since tried to charge a partially discharged lead acid battery using the “Normal” settings with some interesting results. It does the test, then goes to bulk, then flicks back and forth between abs and bulk ad infinitum. This seems to tally with the symptoms of a hardware fault I have read about on here.

---

<div class="post-metadata">

**Author:** ![pwfarnell](https://dub1.discourse-cdn.com/victron/user_avatar/community.victronenergy.com/pwfarnell/32/2341_2.png) [@pwfarnell](https://community.victronenergy.com/u/pwfarnell)\
**Post date:** [7 August 2025 22:58 UTC](https://community.victronenergy.com/t/blue-smart-ip65-12-15-charger-not-charging-lifepo4-battery/42286/2 "2025-08-07T22:58:27Z")

</div>

Yes you seem to have that hardware fault, you will need to refer to your supplier. See thisnpost in particular.

> [@Smart IP65 Charger 15A/12V not charging, switching between bulk and abs, after firmware update](https://community.victronenergy.com/t/smart-ip65-charger-15a-12v-not-charging-switching-between-bulk-and-abs-after-firmware-update/13672/9):
>
> Dear all, We’ve analysed these failures, and they are caused by a hardware defect, and even though rather coincidental, they are not caused by the recent v3.61 firmware update; and also downgrading to an earlier firmware version will not solve the issue. The described behaviour points to a component internal to the unit that has failed. Note that all chargers for which the v3.61 firmware update is available are still within their 5 year warranty term. To get support, including a replacement …