TAB: General
System frequency	50Hz
Shore current	32.0	A
Overruled by remote	checked
Dynamic current limiter	unchecked
External current sensor connected (see manual)	unchecked
State of charge when Bulk finished	85.0	%
Battery capacity	132	Ah
Charge efficiency	1.00	
TAB: Grid
Country / grid code standard	Austria:                 TOR-Erzeuger A V1.1:2019-12
AC input 1	Above selected gridcode plus LOM B (compliant)
TAB: TOR Erzeuger Typ A grid code settings
Use Aux1 as disable FeedIn signal	checked
Maximum AC current for charge or feed in	100.0	%
Maximum generated apparant power	100.0	%
connect waiting time	60	s
connect power ramp	0.0	seconds
low frequency connect value	47.500	Hz
high frequency connect value	50.100	Hz
low voltage connect value	85.00	% Un
high voltage connect value	109.00	% Un
re-connect waiting time	300	s
re-connect power ramp	600.0	seconds
low frequency re-connect value	47.500	Hz
high frequency re-connect value	50.100	Hz
low voltage re-connect value	85.00	% Un
high voltage re-connect value	109.00	% Un
rise-in-voltage protection U>	111.00	% Un
under voltage stage 1	80.00	% Un
under voltage stage 1 delay	1.50	s
over voltage stage 1	115.00	% Un
over voltage stage 1 delay	0.00	s
under frequency stage 1	47.500	Hz
under frequency stage 1 delay	0.00	s
over frequency stage 1	51.500	Hz
over frequency stage 1 delay	0.00	s
under voltage stage 2	77.75	% Un
under voltage stage 2 delay	0.50	s
over voltage stage 2	120.00	% Un
over voltage stage 2 delay	0.00	s
under frequency stage 2	47.000	Hz
under frequency stage 2 delay	0.00	s
over frequency stage 2	53.000	Hz
over frequency stage 2 delay	0.00	s
P(f>) start frequency	50.200	Hz
P(f>) stop frequency	50.200	Hz
P(f>) start delay	0.00	s
P(f>) stop delay	30.00	s
P(f>) droop	5.00	%
P(f<) start frequency	45.000	Hz
P(f<) stop frequency	45.000	Hz
P(f<) start delay	0.00	s
P(f<) stop delay	30.00	s
P(f<) droop	5.00	%
P(U) response	Feed In reduced from Pnominal (= typ a)
Volt-Watt curve voltage V1	90.00	% Un
Max maximuminvert power at V1	100	%
Volt-Watt curve voltage V2	95.00	% Un
Max maximuminvert power at V2	100	%
Volt-Watt curve voltage V3	110.00	% Un
Max maximuminvert power at V2	100	%
Volt-Watt curve voltage V4	112.00	% Un
Max maximuminvert power at V4	0	%
Filter time for P(U)	5.0	s
Reactive power regulation	Use a fixed Cos Phi
Filter time for reactive power	5.0	s
Cos phi at point 1	1.00	
Use lock-in/out	unchecked
TAB: InverterPowerAssist	unchecked

Inverter output voltage	230	V
Inverter DC shut-down voltage	37.20	V
Inverter DC restart voltage	43.60	V
Low DC alarm level	43.60	V
Do not restart after short-circuit (VDE 2510-2  safety)	unchecked
enable AES	checked
Load for starting AES mode	69	W
Offset for ending AES mode	46	W
AES type	search mode
TAB: Charger
Enable charger	checked
Weak AC input	unchecked
Stop after excessive bulk	unchecked
Lithium batteries	unchecked
Storage mode	checked
Use equalization (tubular plate traction battery curve)	unchecked
Charge curve	Adaptive + BatterySafe
Absorption voltage	57.60	V
Float voltage	55.20	V
Charge current	35	A
Repeated absorption time	1.00	Hr
Repeated absorption interval	7.00	Days
Maximum absorption time	8	Hr
Temperature compensation	-64.8	mV/deg
TAB: Virtual switchHTAB: Usage

Virtual switch usage	Do not use VS
TAB: Assistants
TAB: Assistant Configuration
ESS (Energy Storage System) (size:1018)
*)	System uses Gel or AGM batteries
*)	The battery capacity of the system is 132 Ah.
*)	Sustain voltage during the first 24 hours of sustain 46.00 V.
	Sustain voltage after 24 hours 50.00 V.
*)	Cut off voltage for a discharge current of:
	0.005 C= 48.00 V
	0.25 C= 46.60 V
	0.7 C= 45.60 V
	2 C= 44.80 V
*)	Inverting is allowed again when voltage rises 1.20 V above cut-off(0).
*)	Relevant VEConfigure settings:
	  -  Battery capacity 132 Ah.
	  -  PowerAssist unchecked
	  -  Lithium batteries unchecked
	  -  Dynamic current limiter unchecked
	  -  Storage mode checked


Total size of all assistants including the required
(hidden) system assistants is: 1077