question

fulli avatar image
fulli asked

MPPT 75/15 und LiFePO4-Einstellungen

Hallo,

my English is very bad, so I try in German:

Wenn ich meine halb volle 90Ah-Batterie laden will, fängt der Regler auch mit 8-10A an (Bulk), geht dann aber nach einigen Minuten in Absorption, und nach einer Stunde in Float, wo er nur noch mit 2-3A lädt. Erst ein Neustart bringt ihn wieder in die Bulk-Phase. Ist das normal?

Fulli

smart solar set-up help
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

2 Answers
JohnC avatar image
JohnC answered ·

Hallo Fulli. My German is bad too. Just type into 'google translate', then copy/paste to here. Your post comes out as:

If I want to charge my half full 90Ah battery, the regulator also starts with 8-10A (bulk), but then goes into absorption after a few minutes, and after an hour in float, where it only charges with 2-3A. Only a restart brings him back into the bulk phase. Is that normal?

For an answer, yes it's normal if your target Voltages are normal. If your Absorb and Float V's are being maintained then your mppt can do no more. By all means check with a multimeter, but your battery may not be as discharged as you think.


haben Sie einen guten Tag (Have a good day) :)
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

fulli avatar image
fulli answered ·

Hello JohnC

Thank you for the fast answer!

I took 60Ah from the battery the day before and wanted to recharge it as quickly as possible today. But with Float it takes a long time ....

Here my settings:Volker


20190430-102107.jpg (91.2 KiB)
8 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

JohnC avatar image JohnC ♦ commented ·

Maybe take another look at your battery specifications and find a better charge profile. Even a manually entered one.

0 Likes 0 ·
fulli avatar image fulli JohnC ♦ commented ·

OK! I'll raise the constant voltage to 14.4V and see what happens ...

0 Likes 0 ·
JohnC avatar image JohnC ♦ fulli commented ·

Maybe try raising your 'Float' to 13.8V. Safer, and should show some Amps. Don't overdo it..

0 Likes 0 ·
fulli avatar image fulli JohnC ♦ commented ·

Hi!

Today I have started a new attempt: The absorption voltage of 14.4V is reached much too fast, although the battery is only about half full; how can that be?

Volker

0 Likes 0 ·
Matthias Lange - DE avatar image Matthias Lange - DE ♦ fulli commented ·

Woher haben sie die Info, dass die Batterie nur halb voll sei?

Wenn die 14,4V sehr schnell erreicht werden, spricht das eher dafür, das die Batterien doch schon voll sind.

0 Likes 0 ·
fulli avatar image fulli Matthias Lange - DE ♦ commented ·

Hallo M.Lange,

I have written that I have previously taken 60Ah (from the 90Ah battery). Then I returned about 240Wh, and then started the test.

I connected a Guard II and it showed me 13.1V.

Yesterday I loaded the whole day (+ 300Wh), and had 13,2V in the evening.

I do not quite understand Victron's algorithm:

When the controller starts in the morning, it measures the voltage and determines the duration of the absorption. In my case; Battery >12,6V, so absorption time 6 hours x 1/6 = 1 hour, that's too little, because then he goes into float and charges only with 1-2A. I'll try 9 hours today and will see...

Volker



0 Likes 0 ·
Matthias Lange - DE avatar image Matthias Lange - DE ♦ fulli commented ·

Was für eine Batteriespannung wird ihnen über Victron Connect im MPPT angezeigt?

Das ist nämlich die Spannung, nach der der MPPT die Ladekurve regelt.

Was für ein Leitungsquerschnitt wurde vom MPPT zur Batterie verlegt und wie lang ist diese?

Eine Möglichkeit wäre noch, das der Querschnitt zu gering/die Strecke zu lang ist und somit ein hoher Spannungsverlust entsteht(höhere Spannung am MPPT als an der Batterie).

Am MPPT könnte dadurch u.U. schnell die Ladeschlussspannung anliegen und der MPPT regelt herunter.


PS: Sie können mir gerne auch auf deutsch Antworten. :)

0 Likes 0 ·
dennobundy avatar image dennobundy Matthias Lange - DE ♦ commented ·

Hallo, vielleicht können Sie mir auch helfen.

ich bin absolut neu auf diesem Gebiet, ich möchte einen Lifepo4 12V 8Ah Akku i-tecc mit eingebauten BMS mit dem Solarregler 75 / 15 laden. Welche Einstellungen muss ich bei Batterie denn genau machen?

Gruss

Marco

0 Likes 0 ·

Related Resources

Additional resources still need to be added for this topic